Cart (0)

Rhinestone Heat Press Settings: Temperature, Time and Pressure

Heat press settings for hotfix rhinestones: 320-335 °F (160-168 °C), 10-15 seconds, medium to firm pressure, plus iron settings, peeling and quick fixes.

How-to · 5 min read ·

Rhinestone Heat Press Settings: Temperature, Time and Pressure

For hotfix rhinestones, good heat press settings to start with are 320-335 °F (160-168 °C) for 10-15 seconds at medium to firm pressure, with a non-stick sheet or parchment on top. Pre-press the shirt for a few seconds first, and let the design cool a little before you peel the tape slowly and low.

Stones, glues and presses vary, so treat these numbers as a starting point, not a rule. Check your stones' instructions and test on a spare shirt before you press a batch. Pressing is the last step of making a rhinestone shirt, so the design should be cut, filled and lifted on tape by now.

Settings at a glance

Setting Heat press Iron (small pieces)
Temperature 320-335 °F (160-168 °C) Cotton setting, no steam
Time 10-15 seconds 20-30 seconds per spot
Pressure Medium to firm Press hard, don't slide
Cover sheet Non-stick sheet or parchment Non-stick sheet or parchment
Pre-press A few seconds, to dry the shirt Press the area first
Peel Cool a little, peel slowly and low Cool a little, peel slowly and low
Extra hold Inside out, 10 seconds from the back Inside out, press from the back

What each setting does

Temperature. Hotfix stones have heat glue already on the back (hotfix vs non-hotfix explains the difference). Heat melts that glue so it can flow into the fabric. Too little heat and the glue never fully melts.

Time. The heat has to pass through the cover sheet, the tape and the stones before it reaches the glue. Too short a press is a common reason stones fall off later.

Pressure. Pressure pushes the melted glue into the weave of the shirt. With too little, the stones sit on top of the fabric instead of gripping it.

Pre-press. A few seconds of heat dries the shirt and flattens wrinkles. Damp fabric is one of the usual causes of stones falling off.

Cover sheet. A non-stick PTFE sheet or parchment goes between the hot plate and the tape. It protects the tape and keeps the plate clean.

Step by step with a heat press

  1. Set the press to 320-335 °F (160-168 °C) and medium to firm pressure.
  2. Pre-press the shirt for a few seconds to dry it and take out wrinkles.
  3. Fold the shirt and press a light crease to mark the centre.
  4. Place the design with the stones touching the fabric and the tape on top.
  5. Lay a non-stick sheet or parchment over it.
  6. Press for 10-15 seconds.
  7. Let it cool a little, then peel the tape slowly, keeping it low to the shirt.
  8. If a stone lifts, lay the tape back down and press again.
  9. For extra hold, turn the shirt inside out and press for 10 seconds from the back.

Where the design sits matters as much as the heat. Our placement guide shows how to centre it and how far below the collar to put it.

Using an iron

An iron works for small pieces. Set it to the cotton setting with no steam. Press hard for 20-30 seconds on each spot, then lift the iron and move to the next spot. Don't slide it: sliding can shift the stones under the tape.

An iron covers a small area and its heat is less even than a press, so large designs are harder to set well. For big designs and batches, a heat press is easier to get right. Heat press vs iron compares the two in more detail.

Peeling the tape

Let the design cool a little before you peel. Peel slowly, keeping the tape low and close to the shirt rather than pulling it straight up. If a stone comes up with the tape, lay the tape back down over it and press again.

Check the whole design before you put the tape away. A missed stone is easy to fix now.

Fabrics, seams and test presses

Check the shirt's care label before you press. Some synthetic fabrics can scorch or take on a shine under heat, so test on a spare shirt or a hidden spot, such as the inside of the hem.

Seams, collars and zips can hold the plate off the design and leave some stones under-pressed. A pressing pillow or a folded towel inside the shirt lifts the print area so the pressure is even.

When stones don't stay on

Sign Likely cause Fix
Stones fall off right after pressing Too little heat, time or pressure Press again with the cover sheet, check your settings
Stones fall off after the first wash Damp fabric, or washed too soon Pre-press next time, wait 48 hours before washing
A stone lifts during the peel Peeled too soon or too fast Lay the tape back, press again, peel slowly and low

The troubleshooting guide covers problems from cutting to washing, and how to wash rhinestone shirts covers aftercare.

FAQ

What temperature do you heat press rhinestones at?

A good starting point is 320-335 °F (160-168 °C). Glues vary, so check your stones' instructions and test on a spare shirt first.

How long do you press hotfix rhinestones?

10-15 seconds with a heat press at medium to firm pressure. With an iron, press for 20-30 seconds per spot on the cotton setting with no steam.

Do you peel rhinestone transfer tape hot or cold?

Let it cool a little, then peel slowly and low. If a stone lifts, lay the tape back down and press again.

Should I press rhinestones from the back of the shirt?

It helps. For extra hold, turn the shirt inside out and press for 10 seconds from the back.

Why did my rhinestones fall off after pressing?

Usually too little heat, time or pressure, or a damp shirt. Pre-press the shirt to dry it, then press again with the cover sheet.

Templates in this article

Shop all

Keep reading

All guides

New free templates by email.

Sign up and get 20% off your first order.

About twice a month. Unsubscribe any time.