Cart (0)

Rhinestone Template Troubleshooting: Problems, Causes and Fixes

Fix common rhinestone template problems: circles that won't pop out, torn flock, flipped stones, colours that won't line up and stones that fall off.

How-to · 5 min read ·

Rhinestone Template Troubleshooting: Problems, Causes and Fixes

Most rhinestone template problems come from a few causes: a cut that doesn't go all the way through, a dull blade, templates that move between colours, or too little heat, time or pressure. Find your problem in the table below, then read the section for that stage.

Every fix here assumes the template was cut at true size. If the stones don't fit the holes at all, start by checking the file size.

Quick table: problem, cause, fix

Problem Likely cause Fix
Circles won't pop out Not cut through More pressure or a fresh blade
Flock tears while weeding Dull blade Fresh blade
Stones don't fit the holes File resized, or wrong stone size Cut at true size from the matching file
Stones flip upside down Brushing too hard or too few stones Brush in small circles, use more stones than holes, tap the board
Holes stay empty Too few stones, or a circle not weeded Pour on more stones, check each hole is open
Stones stay behind when lifting Tape not rubbed down Rub the tape down well, lift slowly
Colours don't line up Templates moved Line up the boxes, hinge the tape, slide the parchment out
Stones fall off after pressing Too little heat, time or pressure, or damp fabric Pre-press, then press again with the cover sheet
A stone lifts when peeling Peeled too soon or too fast Lay the tape back down and press again

Cutting problems

Circles won't pop out. The blade hasn't cut all the way through the flock. Add pressure or put in a fresh blade, then make a test cut before you cut the full sheet again. How to cut rhinestone templates covers the full setup.

Flock tears while weeding. A dull blade drags at the flock instead of cutting it, and the thin strips between holes tear. Change the blade. Our templates leave at least .03 in (0.76 mm) of flock between holes, so the strips hold up well when the cut is clean.

The template is the wrong size. Some software changes the size on import. Compare it with the size on the product page and set it back. Never resize a template to fit a shirt: the holes would stop matching the stones.

Brushing problems

Stones flip upside down. Brush gently in small circles rather than long sweeps. Use more stones than holes, so there are always stones ready to drop into a gap, and tap the board to help flipped stones turn over.

Holes stay empty. Pour on more stones and keep brushing, then fill the last few by hand. If the same hole never fills, check it was weeded: a circle left in place blocks the hole.

Stones slide around the template. Make sure the template is stuck flat on its backer board, with no lifted edges or bubbles. A template that moves while you brush is hard to fill evenly.

Lifting problems

Stones stay behind when you lift. Rub the tape down well over every stone before you lift, and lift slowly. Use clear hotfix transfer tape made for rhinestones.

Colours don't line up. The templates or the tape moved between colours. Every template in a multi-colour pack has the same cutting box, so when the boxes line up, the colours line up. Lay parchment on the next template, set the tape on top, slide it until the boxes match, tape one edge as a hinge, then slide the parchment out and rub. Multi-colour rhinestone designs walks through it step by step.

Pressing problems

Stones fall off after pressing. The glue didn't melt and grip. The usual causes are too little heat, time or pressure, or a damp shirt. Pre-press the shirt for a few seconds, then press again with the cover sheet. For extra hold, turn the shirt inside out and press for 10 seconds from the back. The heat press settings guide lists the full settings: 320-335 °F (160-168 °C), 10-15 seconds, medium to firm pressure.

A stone lifts when you peel. Let the design cool a little and peel slowly and low. If a stone comes up, lay the tape back down and press again.

The design is crooked or off-centre. Fold the shirt and press a light crease for the centre before you place the design. See the placement guide for height and centring.

Problems after washing

Stones that come off in the wash often point back to pressing or to washing too soon. Wait 48 hours before the first wash, then wash inside out, cold and gentle, and hang to dry. Re-press any loose areas with the cover sheet. How to wash rhinestone shirts has the full routine.

A checklist before you start

  • The file is at true size for your stone size
  • The blade is sharp and the test cut worked
  • Every hole is weeded
  • The template is flat on its backer board
  • You have more stones than holes
  • The shirt is pre-pressed
  • Your settings match your stones' instructions

Practise on a free design

If you are still learning, practise on a free template so a failed cut costs only a sheet of flock.

FAQ

Why won't my rhinestone template circles come out?

The cut didn't go all the way through the flock. Add pressure or put in a fresh blade, and make a test cut before cutting the full sheet again.

Why do my rhinestones keep flipping over?

Brush gently in small circles instead of long sweeps, use more stones than there are holes, and tap the board. Flipped stones usually turn over on their own as you keep brushing.

Why are my rhinestones falling off the shirt?

Usually too little heat, time or pressure, or damp fabric. Pre-press the shirt to dry it, press again with the cover sheet, and add a 10 second press from the back for extra hold.

Why don't my multi-colour templates line up?

The templates or the tape moved. Line up the matching cutting boxes, tape one edge of the transfer tape as a hinge, then slide the parchment out before you rub down the next colour.

Templates in this article

Shop all

Keep reading

All guides

New free templates by email.

About twice a month. Unsubscribe any time.